Success rate is 100 percent ( 5 / 5 ), round - trip min / avg / max = 1 / 26 / 96 ms Success rate is 100 percent ( 5 / 5 ), round - trip min / avg / max = 8 / 27 / 56 ms Thank you again!Īfter script is entered i can then go in an check my IP's using the single line command:+>( tcl ) #} So using what you listed I got this below - please tell me where I am going completely off base on this stuff. I was reading that I could use the proc command to and input my values below, but I am still learning this stuff and am just missing how this is to be called: I was hoping that I could create this file that would allow me to go in at the start of a change and end of a change and run a simple command (such as "address 10.1.1.1", or even something like "address 10.1.1.1 10.2.1.1 10.3.1.1" and have it run the command on all three addresses in one statement. I put in the script you listed, then I tried to initiate this by doing theĬommand, but I got an invalid argument.
CISCO PING SWEEP HOW TO
I am not sure what how to get this to run the way I want. That is good information, but I think I am still stuck on something. Just replace to foreach ip_address $argv and get rid of the procedure. It would be easy to convert back into argv. (potentially ios version dependant as I have read a couple of Josephs posts on similar issues with it)
also its worth to note the tcl traceroute command is finiky, if you use exec it most likely wont work and just hang until all 30 hops are done. Puts "*****Validating path to $ip_address via traceroute*****" Puts "Analysing Ping $counter to IP - $ip_address" However if the ping fails then no traceroute is executed and it goes on to the next IP in the list. What this will do is, if the ping is succesfull then it will go on to execute the traceroute. To make it neater you can create a placeholder variable for all the IP's you want to validate. This means that when you call your proc name it will execute the procedure body using the argument in the proc. To turn it into a procedure you can forget about the argv stuff and just put the ip address directly into the proc argument. After you do that then you can branch off into saving it into flash or whatever. I would recommend for now just turning it into a proc which you can use in the interactive tcl shell on the router. In otherwors "Command line arguments are stored in the list named 'argv" IPAM’s capacity reporting feature not only assists with capacity planning but. Its built-in IP address scanning functionality streamlines and simplifies IP address management strategies.
CISCO PING SWEEP SOFTWARE
tcl are your arguments that argv will soak in SolarWinds IP Address Manager (IPAM) SolarWinds IP Address Manager is an ultimate ping sweep software offering a range of features. The reason why you get an invalid argument is because you are using argv which only accepts arguments when you are calling a tcl script to run from a command line and you add arguments at the end to feed into the script dynamically.Įg if you save a script called pingtest.tcl into the routers flash, then after the. I am learning TCL too and feel I can assist in some of this for you. I don't quite like it because it is not dynamic enough for what I am looking for, and I cannot seem to make this work for trace. Ideally it would be nice if I could runa single line command with each IP address and then when I press enter the script will do the rest.Ī sample of what I would like to do is type: So far I have come acrosss a TcL script that I could use for Ping, but not for trace. My common steps are to ping each of my IP addresses and then I run a traceroute to those IP's to validate they are first reachable and then second I need to validate the path that is being taken is correct before my work and then after my work. I typcially have anywhere from 2 - 10 IP addresses that I need to validate against (typically less than 5 though). I am looking for a script that I can use to help simplify my validation steps when I am doing some work on my devices.
0 kommentar(er)
